300 Hardware Design Engineer jobs in Albuquerque,NM

Recommended

Apply Directly

Field Service Engineer II

EV Group

Rio Rancho, NM 87124

Recommended

Apply Directly

Electronics Engineer III

National Radio Astronomy Observatory

Albuquerque, NM 87101

HybridHealth InsurancePaid Time OffRetirement Benefit

Bachelor of Science in Electrical Engineering, Applied Physics, or a closely related field.
The starting salary/hourly rate of this position is between $99,822-$120,837.
Observatory employees must be authorized to work in the United States.
The Observatory presently cannot sponsor H-1B Visas for this position.
Post-offer, pre-employment/pre-placement drug screen must be successfully passed.
May occasionally be required to work outdoors or climb on antenna to heights greater than 40 feet above the ground.
May be required to travel domestically and internationally by air carrier and to travel by car between NRAO sites.
Experience in design, manufacture, and/or maintenance and repair of receiver systems, microwave antennas and feeds, local oscillators, and microwave/RF mixers and filters (minimum of three years).
Use of various types of electronics test equipment and familiarity with automated test setups to support general test and measurement.

SmartExplore AI is experimental.

New, Posted 3 hours ago

Apply Directly

Fullstack Software Engineer, Micro Platforms

SaidGig

Albuquerque, NM

Apply Directly

Nuclear Engineer

US Navy

Bosque Farms, NM 87068

New, Posted 1 day ago

Recommended

Apply Directly

Sr. Power Electronics Engineer

Raytheon

Albuquerque, NM 87121

OnsiteFlexible ScheduleHealth InsurancePaid Time OffRetirement Benefit

Active and transferable U.S. government issued security clearance is required prior to start date
U.S. citizenship is required, as only U.S. citizens are eligible for a security clearance
Security Clearance Type: DoD Clearance: Secret
Ability to obtain INTERIM U.S. government issued security clearance is required prior to start date
Typically requires a degree in Science, Technology, Engineering or Mathematics (STEM) and a minimum of 5 years of prior relevant experience or an Advanced Degree in a related field and minimum 3 years experience
Experience with any of the following: Power, analog, digital, and / or mixed signal circuit design or analysis and / or digital signal processing
Experience with analog laboratory equipment such as waveform generators, oscilloscopes, spectrum analyzers, and/or network analyzers
Experience with simulation software for circuit analysis or modeling
Experience leading Root-Cause Corrective Action investigations
Experience leading electrical engineering design
Experience with any of the following tools: Mentor Graphics Designer, PSPICE, System Vision, MATLAB, Mathcad, IDL, Computer Simulation Technologies (CST), Microwave Design Studio, High Frequency Structure Simulator (HFSS), Advanced Design System (ADS), SABER RD, SIMPLIS, or xDX Designer
Design and/or Analysis experience with analog electronics design, including at least one of the following: Power supply topologies (buck, boost, buck-boost), FETs/BJTs, op-amp, high/low/band pass filters, clock/data termination, and comparator circuits
Experience with subsystems integration and test, problem investigation, Statistical Process Control (SPC) methods in achieving production yield improvements, technical writing, formal presentation, and implementing Engineering Change Notices
Experience leading or executing Electronics CAD layouts for printed wiring or circuit boards
Self-starter who's capable of working independently as well as with a small technical team. Providing technical oversight and direction, cost estimation, tracking & reporting, coordination, preparation of detailed technical team reports, and proposal support
Demonstrated ability to lead teams to achieve schedule, budget and technical commitments
Experience with project management tools such as Earned Value and/or Agile Execution
Proposal development experience

SmartExplore AI is experimental.

Apply Directly

Manufacturing Engineering Group Leader

Intel Corporation

Albuquerque, NM 87121

OnsiteHealth InsurancePaid Time OffRetirement Benefit

Bachelor's degree in a relevant engineering field or equivalent experience in a specialized field.
4+ years of experience with a bachelor's degree, 3+ years of experience with a master's degree, or no experience required with a PhD.

SmartExplore AI is experimental.

New, Posted 8 hours ago

Apply Directly

Machinist - 1st Shift

ABB

Albuquerque, NM 87121

Onsite

High School Diploma or GED
A minimum of 5 - 10 years' experience or similar environment
Experience in lieu of education will be considered
Knowledge and understanding of the various types of production equipment
Must have good interpersonal skills, able to work with minimal supervision to meet department goals
Good mechanical/electrical abilities
Good communication skills & Interpersonal skills
Ability to read blueprints
Injection molding skills
Ability to communicate, read, write, and understand various written instructions in English
Lift up to 40 Pounds
Stand for long periods
Good hand dexterity
Strong math skills
Capable of operating open setup mill, lathe and surface grinders
Proficient in programming CNC lathe and CNC mill
Repairing molds and tooling while keeping tight tolerances +/- .001"
Understand how to read engineering drawings
Fabricate tooling from engineering drawings
Set up and use a tig welder with a high degree of skill
Use a variety of hand tools and fixtures
Cleans and examines tooling for defects
Verifies dimensions, alignments and clearances, using measuring instruments such as dial indicators, gauge blocks, thickness gauges, and micrometers
Repairs fixtures as necessary
Performs quality checks, interprets and reacts to projects in a timely manner
Takes proactive ownership and responsibility for product quality after fabrication
Operate machine tools (lathe, milling machine, surface grinder, drill press, saws)
Program HAAS CNC laths and mills
Heat treated steels using shop furnace and understanding how to machine hardened steel

SmartExplore AI is experimental.

Recommended

jobsinlogistics.com

Fabrication Floor Manager

Ideum

Corrales, NM 87048

~ 32 min Onsite

Minimum of 5 years' hands-on experience in fabrication, including both traditional shop practices and digital fabrication (CNC, laser cutting, etc.)
Strong familiarity with a range of materials, including wood, plastics, and metals
Excellent working knowledge of shop tools and safety protocols
Demonstrated experience managing people and coordinating complex build schedules
Ability to read and interpret CAD files and fabrication drawings
Excellent communication skills and the ability to collaborate across teams
Self-motivated and organized, with the ability to manage shifting priorities in a fast-paced environment

SmartExplore AI is experimental.

New, Posted 1 day ago

Maintenance Repairer

The Clyde Hotel

Albuquerque, NM 87104

New, Posted 20 hours ago

Apply Directly

Technical Writer and Editor (Technical Editor and Writer 4) - 28988

HII

Albuquerque, NM 87121

OnsiteEducation AssistanceHealth InsurancePaid Time OffRetirement Benefit

10 years of relevant experience with bachelor's in related field; 8 years of relevant experience with master's in related field; or High School Diploma or equivalent and 14 years relevant experience
Demonstrated minimum of 5 years of experience proofreading others' work and providing clear, constructive feedback to improve accuracy and quality
Active Secret Clearance
Ability to obtain and maintain a Top Secret Security Clearance with active SCI
Excellent written and verbal communications in the English language
Proficiency with desktop publishing software such as Adobe products and Microsoft Office suite
Ability to manage time and effort across multiple simultaneous projects
Highly organized and detail oriented

SmartExplore AI is experimental.