1092 Test Technician jobs in Alabama

A good driving record and a valid driver's license in the state you are applying.
We want to train you! You will need to have the aptitude and ability to learn to use RF, digital and Volt-Ohm meters and other related equipment to interpret data and use information to solve problems and determine optimal signal routing.
Flexibility to go above and beyond for our customers by working overtime and on-call as needed.
Problem solving is key when working with our customers.
Be able to listen to customers and present solutions in a positive manner.
Due to the nature of the position you will need to successfully work in small and confined areas;
Lift to 80 lbs.;
Work on a ladder;
And work in all weather conditions.
You will have demonstrated at least 3 months of customer service or related experience and/or training.
The equivalent combination of education and experience is also acceptable.
High school diploma or GED.
Regular and predictable attendance is required.
Job offers are contingent upon the results of background, drug screening, and reference check.

SmartExplore AI is experimental.

Apply Directly

Electrician

Sjs Executives Llc

Montgomery, AL 36109

$29.01/hr

OnsiteUrgently HiringPaid Time Off

Possession of a valid Real ID is a requirement for this position
Minimum of 3 years of commercial, institutional, industrial, or healthcare electrical experience
Experience installing, maintaining, and repairing electrical distribution systems, wiring, panels, circuits, and electrical equipment
Knowledge of single-phase and three-phase electrical systems and power distribution
Experience troubleshooting electrical systems using industry-standard testing and diagnostic equipment
Ability to read and interpret electrical blueprints, wiring diagrams, schematics, and technical documentation
Knowledge of electrical calculations including voltage, current, resistance, power factor, and voltage drop
Familiarity with electronic components such as resistors, capacitors, and transistors
Ability to lift up to 50 pounds frequently and 75 pounds occasionally
Ability to work on ladders, at elevated heights, and in confined spaces
Ability to work in hot environments and around energized equipment, machinery, dust, chemicals, oils, fumes, and other occupational hazards
Ability to stand, bend, kneel, and perform physically demanding work for extended periods
Ability to wear an OSHA-approved respirator when required and successfully complete required fit testing
Ability to wear required personal protective equipment (PPE), including steel-toe boots, eye protection, hearing protection, and approved face protection
OSHA 30-Hour Construction certification preferred
Must be able to successfully pass a drug test and a thorough background check for access onto a military installation; the background check extends past 7 years

SmartExplore AI is experimental.

Apply Directly

Maintenance Technician

Pitstop Car Wash

Mobile, AL 36602

OnsiteHealth InsurancePaid Time OffRetirement Benefit

Strong mechanical aptitude (you can take things apart and put them back together)
Submit a valid driver's license
Successfully pass a company insurance review authorizing them to operate fleet vehicles
Insurance approval is required prior to the start date
Lifting up to 60LBS
Constant movement throughout the day
Bending, reaching, climbing, and working around equipment

SmartExplore AI is experimental.

Recommended

Apply Directly

QA Technician

Atlas Copco

Bay Minette, AL 36507

Onsite

High School Diploma or GED
Prior test experience.
Capacity to lift and transport a minimum of 50 pounds.
Ability to climb, twist, turn, bend, stoop, kneel, push loads, and work at moderate elevations.
Must exhibit flexibility and be a collaborative team member.
Reliably maintain an exceptional attendance record

SmartExplore AI is experimental.

Apply Directly

NDT Technician II

Teledyne

Huntsville, AL 35810

Onsite

NDT Level II certification in Leak Testing (LT) - Helium Mass Spectrometer in accordance with employer written practice per SNT-TC-1A, NAS 410, or CP-189 as applicable
Demonstrated hands-on experience with helium leak detection systems, vacuum technology, and leak rate measurement
Working knowledge of ASME Section V Article 10, and applicable ASTM standards (E493, E498)
Ability to read and interpret codes, standards, specifications, drawings, and procedures
Requires a high school diploma
Prefer candidate have a BS degree in a recognized field of engineering or a closely related field of science
Normally requires approximately ten (10) years of applicable professional experience or a combination of graduate study and experience
US Citizenship with ability to attain/maintain government security clearance.
Helium mass spectrometer operating principles and tracer gas behavior
Vacuum system theory, operation, and troubleshooting
Leak rate units and interpretation (atm• cc/sec)
Calibration standards and sensitivity verification
Applicable codes and customer specification requirements

SmartExplore AI is experimental.

New, Posted 10 hours ago

HVAC Technician

HEXCEL CORPORATION

Decatur, AL 35609

Easy Apply

Assembly Maintenance Supervisor - 2nd shift

Adecco

Mc Calla, AL 35111

$85,000-$105,000/yr

Onsite

1+ year of maintenance leadership or supervisory experience
Preventative maintenance experience required
Automotive manufacturing experience required
Experience supporting automated manufacturing equipment
Bachelor's degree in Electrical Engineering, Industrial Technology or another technical discipline plus 3+ years of automated manufacturing maintenance experience
Associate degree in Electronics Technology plus 5+ years of automated manufacturing maintenance experience
7+ years of experience in a similar maintenance leadership role within an automated manufacturing environment
Working knowledge of hydraulic, pneumatic, mechanical and electrical systems
Experience troubleshooting PLC-controlled equipment and robotics
Allen Bradley PLC experience, including RSLogix 500, RSLogix 5000, PanelView and PanelView Plus preferred
Ability to operate hand tools, power tools and shop equipment
Proficient with Microsoft Word, Excel and PowerPoint
Excellent troubleshooting, problem-solving and analytical skills
Strong communication and leadership abilities
Ability to prioritize work in a fast-paced manufacturing environment